Removing stripped collimator screw

Anex ANH2-065 stripped screw extraction kit

I've mentioned earlier that one of the collimator screws on my Celestron NexStar 6SE telescope was completely stuck, preventing proper calibration. It was so bad that the screw's head became stripped in the attempts to unscrew it, and pliers were of no use, either. To fix this problem, I ordered Anex ANH2-065, a stripped screw extraction kit made in Japan for US$20. It had a lot of favourable reviews, so I thought I might as well try it.

The kit came with two drill bits, one for working with 2.5 to 3mm screws (red) and the other, 4 to 5mm screws (yellow). One end of each bit is used for drilling a small hole in the middle of the screw and the other end is a reverse-threaded tap that gets inserted into this hole. As you turn the bit counter-clockwise, the tap burrows into the screw. Eventually, the screw is supposed to turn with it and come out.

Insert the drill bit into stripped screw

NexStar 6SE's collimator screw is the same one used with C6, an M3 (3mm) type with 12mm length, so I got my old cordless drill charged up and inserted the red bit. I set the torque level to low to reduce the risk of damage, and carefully drilled out a tiny hole about 4mm deep into the stuck screw.

Screw the reverse-threaded tap into the drilled hole

Then I took the bit out, turned it around, and placed the reverse-threaded tap side into the hole. To turn the tool counter-clockwise by hand, I attached a handle that came with the kit. For a while, the tap slowly descended into the screw without anything happening.

The stubborn screw finally comes out

When the tap was firmly anchored into the screw, a budge created a small creaking sound and the screw finally began to turn. It became loose and was able to come out. It was very satisfying to see this happen, especially because the telescope body was unharmed.

The replacement and the replaced

You can see what happened to the once-stubborn screw here, compared with the replacement screw I had ordered separately. Pretty interesting. I removed and the replaced all the collimator screws one by one with ease after this ordeal.

Trackbacks

Trackback specific URI for this entry

This link is not meant to be clicked. It contains the trackback URI for this entry. You can use this URI to send ping- & trackbacks from your own blog to this entry. To copy the link, right click and select "Copy Shortcut" in Internet Explorer or "Copy Link Location" in Mozilla.

Wesley's Tool-Box on : First good Jupiter shots from NexStar 6SE

Continue reading "First good Jupiter shots from NexStar 6SE"
Getting sharper image of Jupiter from SX50 HS without using integrated zoom After fixing the collimator screw problem, I spent some time getting my Celestron NexStar 6SE properly collimated. To see if this improved the sights, I pointed the telescope to

Wesley's Tool-Box on : DIY artificial star for SCT collimation

Continue reading "DIY artificial star for SCT collimation"
Using a Schmidt-Cassegrain telescope (SCT) like my Celestron NexStar 6SE requires the secondary mirror to be collimated properly to get a crisp image. I've done the collimation after fixing the screws, but I wanted to fine-tune further. The adjustment I w

Comments

Display comments as Linear | Threaded

No comments

Add Comment

E-Mail addresses will not be displayed and will only be used for E-Mail notifications.

To prevent automated Bots from commentspamming, please enter the string you see in the image below in the appropriate input box. Your comment will only be submitted if the strings match. Please ensure that your browser supports and accepts cookies, or your comment cannot be verified correctly.
CAPTCHA

Enclosing asterisks marks text as bold (*word*), underscore are made via _word_.
Standard emoticons like :-) and ;-) are converted to images.

Copyright (C) 1996-2024 Woo-Duk Chung (Wesley Woo-Duk Hwang-Chung). All rights reserved.